Chubb 3R63 Electromechanical Mortice Pass Lock LH
Chubb 3R63/002/01/S Electromechanical Mortice Pass Lock Left Hand with ILU (Inner Locking Unit - keyway)
To provide secure locking of swinging passage / control doors using third party security management systems (SMS) or conventional key control. Designed to
enable key and electric operation from both sides of the door. This lock is specifically designed for very high use applications; typically securing
perimeter doors and main access routes.
The 3R63 is a mortice lock of robust construction based on the Chubb Locks
Custodial Services large mortice footprint. It has a substantial bolt designed to
be withdrawn by means of a large ‘T’ handle or lever handle, on either side of
the lock, whether opening or closing the door. The face of the bolt is angled so that it will slam shut in an
emergency, but excessive slamming is not recommended and
may lead to premature wear and failure. Locking is achieved by means of a completely separate (and
interchangeable) inner locking unit, operable from either side, the vertically sliding bolt of which, engages in a
recess in the main bolt: alternatively, a plunger controlled by the solenoid unit, operates in a similar manner
at the rear end of the bolt.
Principal of Operation
Electrical Mode – Locking/unlocking by 24 Volt DC controlled sequence from an external source (SMS).
Bolt withdrawal by handle, which should also be used when engaging the bolt to secure the door.
Manual Mode – Locking/unlocking achieved using conventional (mechanical key). Bolt withdrawal by
handle, which should also be used when engaging the bolt to secure the door.
Manual Override – In the event of power or communication failure an override key is used to disable the
electric locking function.
Standard Features
Solid Case Technology; Lock case machined from single piece carbon steel block.
25mm throw solid steel main bolt fitted with antisaw Tungsten Carbide rollers
Dual solenoid electric locking latch.
Independent 8lever locking mechanism.
Lock provides status monitoring of critical functions and tamper.
Integral baffle arrangements to resist manipulation and interference via the keyhole.
Dedicated key profile operates 3A63/3A73/3R63 group of locks only.
Performance/Testing/Standards
Mechanical locking mechanism tested to a minimum of 300,000 operations.
Solenoid locking unit tested to a minimum of 1,000,000 cycles.
Saw attack on the main bolt 12 hours.
Solenoid arrangement designed to operate at +/10% of 24V DC regulated supply.
Nominal operating current 500mA.
End load 13.5 kN
Side Load 25 kN
Additional Items
Range of handle / knob options
Gate Box
Lock Interface Unit to facilitate operation by commercial access control systems
Door cable
Reinforcing plates for use on wooden doors
Dimensions & Weights
Case Height 207mm
Case Length 229mm
Case Thickness 29mm
Bolt Throw 25mm
Bolt Depth 45mm
Bolt Thickness 22mm
Weight (lock only) 10.5kg
Finish:
Lock case carbon steel electroplated.
Main bolt carbon steel electroplated.
Main bolt follower – high tensile brass.
Keys – hardened steel
Levers and springs – brass / phosphor bronze.
The 3R63 is a mortice lock of robust construction based on the Chubb Locks
Custodial Services large mortice footprint. It has a substantial bolt designed to
be withdrawn by means of a large ‘T’ handle or lever handle, on either side of
the lock, whether opening or closing the door. The face of the bolt is angled so that it will slam shut in an
emergency, but excessive slamming is not recommended and
may lead to premature wear and failure. Locking is achieved by means of a completely separate (and
interchangeable) inner locking unit, operable from either side, the vertically sliding bolt of which, engages in a
recess in the main bolt: alternatively, a plunger controlled by the solenoid unit, operates in a similar manner
at the rear end of the bolt.
Principal of Operation
Electrical Mode – Locking/unlocking by 24 Volt DC controlled sequence from an external source (SMS).
Bolt withdrawal by handle, which should also be used when engaging the bolt to secure the door.
Manual Mode – Locking/unlocking achieved using conventional (mechanical key). Bolt withdrawal by
handle, which should also be used when engaging the bolt to secure the door.
Manual Override – In the event of power or communication failure an override key is used to disable the
electric locking function.
Standard Features
Solid Case Technology; Lock case machined from single piece carbon steel block.
25mm throw solid steel main bolt fitted with antisaw Tungsten Carbide rollers
Dual solenoid electric locking latch.
Independent 8lever locking mechanism.
Lock provides status monitoring of critical functions and tamper.
Integral baffle arrangements to resist manipulation and interference via the keyhole.
Dedicated key profile operates 3A63/3A73/3R63 group of locks only.
Performance/Testing/Standards
Mechanical locking mechanism tested to a minimum of 300,000 operations.
Solenoid locking unit tested to a minimum of 1,000,000 cycles.
Saw attack on the main bolt 12 hours.
Solenoid arrangement designed to operate at +/10% of 24V DC regulated supply.
Nominal operating current 500mA.
End load 13.5 kN
Side Load 25 kN
Additional Items
Range of handle / knob options
Gate Box
Lock Interface Unit to facilitate operation by commercial access control systems
Door cable
Reinforcing plates for use on wooden doors
Dimensions & Weights
Case Height 207mm
Case Length 229mm
Case Thickness 29mm
Bolt Throw 25mm
Bolt Depth 45mm
Bolt Thickness 22mm
Weight (lock only) 10.5kg
Finish:
Lock case carbon steel electroplated.
Main bolt carbon steel electroplated.
Main bolt follower – high tensile brass.
Keys – hardened steel
Levers and springs – brass / phosphor bronze.